CellarPro Mounting Clips 1800 2-Pk #1092-R

16 Reviews
SKU: 1092 Mounting Clips 2-Pk RETROFIT
In Stock

Usually Ships w/i 1-2 Days

Shipping Information:

FedEx / UPS / USPS / Saver


Mount to the front of CellarPro 1800 Series cooling units and are bolted to the ceiling inside the wine cellar. This is a retrofit item, and not for factory installation.


CellarPro Mounting Clips 1800 2-Pk (P/N 1092-R). Two mounting clips can attach anywhere along the front of CellarPro 1800 cooling units and offer predrilled slots for bolting to the ceiling of the wine cellar. Framing is required in or above the ceiling.


  • Includes 2 mounting clips for to be used with CellarPro 1800 Series cooling units
  • Easily clips into the front/top edge of the cooling unit
  • Includes a pre-drilled slot for bolting to the ceiling
  • Requires framing in the ceiling to support the weight of the cooling unit


Specs & Resources

Size: 1.5w x 2d x 3/8h

Weight: 0.1 lbs

Work as expected


They work great for what they are, but the price is rather high. It would be nice if they were included with the cooling units. Easy to install and they hold the cooling unit in place as expect.

Worked great but agree they should have been included.


I discovered that they weren’t included which delayed my installation a week while I waited for them to be mailed. Did not see that they were extra when ordering. Website should be configured to ask you if you need them when you’re checking out because it wasn’t obvious or better yet, just include them. Seriously, they couldn’t impact your bottom line that much! I’m deducting a star because of this. The clips themselves work great and like somebody else noted, I too used washers to make sure the screws did not slip through the holes.



I have two cellars from CellarPro and needed a set of these clips to replace one unit. CellarPro was nice enough to send me a set after purchasing the replacement cooler. Worked great as usual

recent customer

by -

They don't look impressive at first, but do the job perfect!

The clips work as expected


I had no issue with installing the clips on the front of the CellarPro. I agree that they will not easily support the full weight of the unit until they are bolted down, so plan to support the unit during installation. I also used washers to spread the load over a greater area of the clips. As noted in another review I have published, the combination of the clip configuration and the front grill of the CellarPro made sealing the unit a bit of a challenge. But in the end, they worked as expected. I agree, they should be part of the package....

Rip Off Clips


The fact that they make you pay 10.00 for this junk is a stain on an otherwise excellent company.
<br>These should be included with the unit or at least be a no cost option.
<br> They cant cost more than .50 to make.
<br>When I installed them,
<br>they bent easily and were hard to work with. I had to install backing nuts on the all-thread
<br>because they wouldn't support the weight without bending.

these clips work just fine


I was skeptical when I opened the package of mounting clips, however, I found that they work just fine. The old mounting ears from the Grand Cru cooler I was replacing wouldn't work as the cellar pro is a larger unit. So, I snapped them into place on the cooler before mounting it in the cabinet. Once I got the 1800QT into the opening in the cabinet, I was able to prop it up with a piece of wood, pre-drill some screw holes, and attach the screws. Extremely simple design made it easy to use.
<br>I do agree with Richard's review that these could be included in the default package, but I understand that many people wouldn't need them, so I don't really find fault with having the buy them. Cheap compared to the wine. :)



Would not buy these , they are cheaply made and a shelf is better

Better than nothing, barely,


After seeing how well the other components I purchased were made, I was very disappointed with these clips. They didn't fit without serious modification, and even after than I'm not really pleased with them. Will make my own supports first chance I get.<BR><br><b><i>Reply from Manufacturer:</i></b><BR><i>These clips do not need any modification whatsover. &nbsp;Simply remove the grill cover, then clip the short end under the case cover -- that's all there is to it...</i>



Why aren't these included?????

Just ok ... not by much.


Concept is also a bit weak. They catch a small folder of metal at the top of the unit. In my case the clips did not pull the unit all the way up the top of the frame. The work but not well and I agree that they should be included with the unit.

Overpriced but needed


Got to have them.. They should be included.



These clips are ridiculously overpriced and necessary for the mounting of this unit. I concur, they should be included with the item upon purchase......... add shipping costs to these overpriced pieces of metal and you've got a real burn job!

Overpriced, but needed


$25! These should be included with the otherwise highly rated unit at no cost.



As it turned out, these clips were not needed. I have mailed them back and I hope you have credited the $10 to my account. As I said at order time - $10 for these clips was gouging. After spending $1000 for the cooling unit, $10 for the clips was an insult.

Mounting clips


If your old unit has clips, use them. You won't have to drill new holes. One of the new clips I bought was extremely difficult to fit - the "fold over" was too tight. I never did get it on perfectly and I would have had great difficulty moving it for alignment - fortunately the old Breezaire clips fitted perfectly.